Go to machine shop get a piece of 1/2 inch steel plate drill holes for the
size dowel you want in it. Cut wood to approx size but a little large,
chamfer one end to fit in proper hole, hit with hammer, short dowel of
proper size falls out bottom of steel plate.
"Kevin B" <[email protected]> wrote in message
news:tnJMb.37221$sv6.110028@attbi_s52...
> Folks,
> Pardon my ignorance, but is there a tool I can get that will make
small
> dowels. Let say 2 to 3 inches long by 1/4 or 3/8 diameter.
>
> Thank you,
>
> Kevin B
>
>
In article <OxNMb.76822$X%5.13802@pd7tw2no>, JohnV
<[email protected]> wrote:
> I have posted an interesting way to do this with a router and a bullnose bit
> in alt.binaries.pictures.woodworking.. Can't remember the source so if
> anyone recognizes it please help me give credit where due.
It looks a lot like the demo I saw on The Router Workshop last spring.
They were making oak dowel for a towel rack IIRC.
djb
--
There are no socks in my email address.
"Quando Omni Flunkus Moritati"
On Tue, 13 Jan 2004 03:13:30 GMT, Kevin B wrote:
>
> Folks,
> Pardon my ignorance, but is there a tool I can get that will make small
> dowels. Let say 2 to 3 inches long by 1/4 or 3/8 diameter.
>
> Thank you,
Lie Nielsen make dowel plates in either imperial or metric. I've just
used my metric plate to make some dowels to pin some tenons on a
cabinet I'm making. Made the dowels out of oak.
Aswell as dowels for pinning tenons, I use dowels for breadboard ends
so it was a good investment for me.
Dowels for doweled joints I buy ready made - bashing bits of wood
through a hole in a plate is tedious & best avoided if at all
possible.
The good thing about the dowel plate is that the grain of the wood
lines up along the length of the dowel as it's punched through ie.
it's not severed like doweling you buy. Therefore, it's got a good
deal more strength than dowel that's been cut, although I haven't
tested that empirically.
--
Frank
http://www.freebsd.org/
> Pardon my ignorance, but is there a tool I can get that will make
small
> dowels. Let say 2 to 3 inches long by 1/4 or 3/8 diameter.
>
Sure is. Available at Lee Valley.
http://tinyurl.com/ypqwk
--
Regards,
Dean Bielanowski
Editor,
Online Tool Reviews
http://www.onlinetoolreviews.com
------------------------------------------------------------
Latest 5 Reviews:
- Workshop Essentials Under $30
- Festool PS 300 Jigsaws
- Delta Universal Tenoning Jig
- Ryobi Reciprocating Saw
- Infinity Router Bits
------------------------------------------------------------
On Tue, 13 Jan 2004 03:13:30 GMT, "Kevin B" <[email protected]>
wrote:
>Folks,
> Pardon my ignorance, but is there a tool I can get that will make small
>dowels. Let say 2 to 3 inches long by 1/4 or 3/8 diameter.
>
>Thank you,
>
>Kevin B
>
yes.
On Tue, 13 Jan 2004 03:13:30 GMT, "Kevin B" <[email protected]>
wrote:
>Folks,
> Pardon my ignorance, but is there a tool I can get that will make small
>dowels. Let say 2 to 3 inches long by 1/4 or 3/8 diameter.
>
>Thank you,
>
>Kevin B
>
Most woodworkers buy dowels. One time I needed walnut dowels and made
them on my router table starting with square stock and using a
round-over bit. I could use my lathe, with the added benefit of easy
sanding.
Almost right. Don't cut the wood.
Find a straight grained piece and split it.
Art
"Sweet Sawdust" <[email protected]> wrote in message
news:[email protected]...
> Go to machine shop get a piece of 1/2 inch steel plate drill holes for the
> size dowel you want in it. Cut wood to approx size but a little large,
> chamfer one end to fit in proper hole, hit with hammer, short dowel of
> proper size falls out bottom of steel plate.
>
> "Kevin B" <[email protected]> wrote in message
> news:tnJMb.37221$sv6.110028@attbi_s52...
> > Folks,
> > Pardon my ignorance, but is there a tool I can get that will make
> small
> > dowels. Let say 2 to 3 inches long by 1/4 or 3/8 diameter.
> >
> > Thank you,
> >
> > Kevin B
> >
> >
>
>
Thank you Dave. Was the Router Workshop. www.routerworkshop.com
JohnV
"Dave Balderstone" <[email protected]> wrote in message
news:140120041746180351%[email protected]...
In article <OxNMb.76822$X%5.13802@pd7tw2no>, JohnV
<[email protected]> wrote:
I have posted an interesting way to do this with a router and a bullnose
bit
in alt.binaries.pictures.woodworking.. Can't remember the source so if
anyone recognizes it please help me give credit where due.
It looks a lot like the demo I saw on The Router Workshop last spring.
They were making oak dowel for a towel rack IIRC.
djb
There are no socks in my email address.
"Quando Omni Flunkus Moritati"
I have posted an interesting way to do this with a router and a bullnose bit
in alt.binaries.pictures.woodworking.. Can't remember the source so if
anyone recognizes it please help me give credit where due. I have also had
instruction at some time on how to do this on a tablesaw with a jig that
consists of two pieces of wood, one with a square hole and the other with a
round. unfortunatley I cant find that literature. Good luck.
John V
"Kevin B" <[email protected]> wrote in message
news:tnJMb.37221$sv6.110028@attbi_s52...
> Folks,
> Pardon my ignorance, but is there a tool I can get that will make
small
> dowels. Let say 2 to 3 inches long by 1/4 or 3/8 diameter.
>
> Thank you,
>
> Kevin B
>
>
Kevin B writes:
> Pardon my ignorance, but is there a tool I can get that will make
small
> dowels. Let say 2 to 3 inches long by 1/4 or 3/8 diameter.
I don't want to rain on your parade, but why bother?
You can buy packages of serrated dowels from lots of supply houses at very
modest cost.
It's hardly worth the effort.
--
Lew
S/A: Challenge, The Bullet Proof Boat, (Under Construction in the Southland)
Visit: <http://home.earthlink.net/~lewhodgett> for Pictures
On Tue, 13 Jan 2004 03:13:30 +0000, Kevin B wrote:
> Folks,
> Pardon my ignorance, but is there a tool I can get that will make small
> dowels. Let say 2 to 3 inches long by 1/4 or 3/8 diameter.
>
> Thank you,
>
> Kevin B
Make a subbase for your router. Say, about an inch thick (at least in the
center) For a 3/8" dowel drill a hole straight across the center 3/8"
diameter. Enlarge this hole to around 9/16", if my math is correct, half
way across, to the point where the router bit drops down. Use a 1/2 or
3/4 inch straight bit in the router, cut a slot in the center where the
bit drops down for chip clearance. (I wish I could draw a picture...)
The square strips should just fit in the large hole, the turned pieces
should just fit in the small hole when the router is set correctly. Then
you can rip 3/8" x 3/8" square strips on the saw, slide them in the large
hole while the router is on, rotating them as they pass through. You will
have to play with the settings some but this jig will give you accurate
3/8" dowels... same setup could do 1/4" dowels. Minimum length will be
about 7" with a standard router base, they can be cut to length after
turning. The jig works really well with longer pieces, like 36" lengths.
Kevin B wrote:
> Folks,
> Pardon my ignorance, but is there a tool I can get that will make
> small
> dowels. Let say 2 to 3 inches long by 1/4 or 3/8 diameter.
Sure. Get a wood lathe. :)
--
Michael McIntyre ---- Silvan <[email protected]>
Linux fanatic, and certified Geek; registered Linux user #243621
http://www.geocities.com/Paris/Rue/5407/