Folks -
Okay, the PO of this saw had scuffed up the side of the rip fence with the
blade, doing what, I'm not sure. The fence looks like it's made of out
lamintated BB ply, but I don't know how to fence panels come off. I know
that I could go caveman on it, but I thought someone here would likely have
more finess than my own bad self.
I'd sure appreciate some input. I can't really tune the saw up until I get
the fence fixed.
John Moorhead
Lakeport, CA
john moorhead wrote...
> Folks -
>
> Okay, the PO of this saw had scuffed up the side of the rip fence with the
> blade, doing what, I'm not sure. The fence looks like it's made of out
> lamintated BB ply, but I don't know how to fence panels come off. I know
> that I could go caveman on it, but I thought someone here would likely have
> more finess than my own bad self.
You're right. The panels are made of baltic birch ply. The panels are
screwed into the steel box beam, the laminate is (contact) cemented to
the ply, and then the edging is inserted. To remove a panel, you have to
peel off the laminate, which unfortunately will destroy it.
Jim
Fly-by-Night CC wrote...
> In article <[email protected]>,
> "FOW" <[email protected]> wrote:
>
> > Maybe a heatgun would work
> > also.
>
> Yep, that's the way I removed mine. The cement softened right up and I
> peeled the formica off in one big piece with no problem whatsoever.
> Underneath are maybe 8 hex-head screws holding the birch to the metal
> tube.
>
>
Well, slap my 'fro! I sit corrected. Truth is, I didn't even try to
preserve mine, because the panel was getting replaced, anyway. I was
increasing the fence height.
Jim
I believe there are screw heads hidden beneath the laminate. I'd scuff
sand it and laminate another layer on top.
Bridger
On Sun, 28 Dec 2003 01:29:30 GMT, "john moorhead"
<[email protected]> wrote:
>Folks -
>
>Okay, the PO of this saw had scuffed up the side of the rip fence with the
>blade, doing what, I'm not sure. The fence looks like it's made of out
>lamintated BB ply, but I don't know how to fence panels come off. I know
>that I could go caveman on it, but I thought someone here would likely have
>more finess than my own bad self.
>
>I'd sure appreciate some input. I can't really tune the saw up until I get
>the fence fixed.
>
>John Moorhead
>Lakeport, CA
>
In article <[email protected]>, "Slowhand" <I'm@work>
wrote:
> One note I might add is when you re-laminate the strip back together, make
> it so you can remove the baltic birch from the metal part easily (i.e.
> expose the connection). I did this because I have different fence
> attachments. From the fwiw dept.
How did you do this? I suppose you could relaminate the ply detached
from the tube, drill throught the backside to locate the screw holes...?
--
Owen Lowe and his Fly-by-Night Copper Company
Offering a shim for the Porter-Cable 557 type 2 fence design.
<http://www.flybynightcoppercompany.com>
<http://www.easystreet.com/~onlnlowe/index.html>
In article <[email protected]>,
"FOW" <[email protected]> wrote:
> Maybe a heatgun would work
> also.
Yep, that's the way I removed mine. The cement softened right up and I
peeled the formica off in one big piece with no problem whatsoever.
Underneath are maybe 8 hex-head screws holding the birch to the metal
tube.
--
Owen Lowe and his Fly-by-Night Copper Company
Offering a shim for the Porter-Cable 557 type 2 fence design.
<http://www.flybynightcoppercompany.com>
<http://www.easystreet.com/~onlnlowe/index.html>
"Fly-by-Night CC" <[email protected]> wrote in
> Underneath are maybe 8 hex-head screws holding the birch to the metal
> tube.
One note I might add is when you re-laminate the strip back together, make
it so you can remove the baltic birch from the metal part easily (i.e.
expose the connection). I did this because I have different fence
attachments. From the fwiw dept.
SH
Get one corner of the Lam. up then use a squirt bottle of lacquer thinner to
squirt under the lam and peel off the lam with a sharp putty knife. Or try
Acetone. Watch the paint on the fence though. Maybe a heatgun would work
also.
"Jim Wilson" <[email protected]> wrote in message
news:[email protected]...
> john moorhead wrote...
> > Folks -
> >
> > Okay, the PO of this saw had scuffed up the side of the rip fence with
the
> > blade, doing what, I'm not sure. The fence looks like it's made of out
> > lamintated BB ply, but I don't know how to fence panels come off. I
know
> > that I could go caveman on it, but I thought someone here would likely
have
> > more finess than my own bad self.
>
> You're right. The panels are made of baltic birch ply. The panels are
> screwed into the steel box beam, the laminate is (contact) cemented to
> the ply, and then the edging is inserted. To remove a panel, you have to
> peel off the laminate, which unfortunately will destroy it.
>
> Jim
In article <[email protected]>, "FOW"
<[email protected]> writes:
>Get one corner of the Lam. up then use a squirt bottle of lacquer thinner to
>squirt under the lam and peel off the lam with a sharp putty knife. Or try
>Acetone. Watch the paint on the fence though. Maybe a heatgun would work
>also.
If this method is used don't forget to use flame-retardant all over your body.
But on the other hand if you are in an enclosed place the explosion will kill
you. :)
Please don't use the heat gun in conjunction with either of these volatile
compounds!
Roy
Roy