Frost line insulation???

I insulated the outside of my foundation with ridgid foam insulation. My
foundation is exposed by about 18 inches, so I used 4 x 8' sheets horizontally.
So yes I had to do some digging, and I applied a concrete base brush on
material to cover the foam, and used some drip edge to cover the top. This was
approved by my utility company for basement insulation, and it does make for a
warmer basement, and smaller fuel bills.
Just my 2 cents.

Blair Chesterton wrote:

> I am looking for something to insulate the upper four feet of my basement
> shop other than the fiberglas insulation I presently use. I don't want to
> lose too much space in the shop to walls so I would like to find something
> that has a decent "R" value and isnt that thick. What types of methods are
> available? I have considered removing this insulation and just having the
> poured concrete walls but don't know how much effect that might have on my
> heating bill and comfort level.

I'd use styrofoam insulating panels cut to fit between the studs.

--
Jack Novak
Buffalo, NY - USA
(Remove "SPAM" from email address to reply)

I actually have two different barriers. My home is right next to the ocean,
and we get a lot of salt spray, and horizontal rain, so I have painted the
concrete with drylok waterseal, the foam, and then a vapor barrier, all
under the plywood.

Dave

"Michael Daly" <[email protected]> wrote in message
news:[email protected]...
> On 23-Nov-2003, "David Babcock" <[email protected]> wrote:
>
> > I put up a vapor barrier, then placed the insulation against it,
>
> Did you put the vapour barrier _outside_ the insulation?
>
> Mike

"David Babcock" <[email protected]> wrote in message
news:zNfwb.90993$Dw6.452986@attbi_s02...
> What I have on the exposed concrete section of my workshop is a Dow
product
> called Polyisocynurate Insulation. It comes with a foil skin on both sides
> and is available in various thickness's and R values
> 1/2"........R3.3
> 5/8"........R4.1
> 3/4"........R5.0
> 1"...........R6.5

This is a good material, but check it for cost effectiveness as compared
some others. Foam bead board (the white stuff) is R4 per inch versus the
6.5
Ed

On 23-Nov-2003, "David Babcock" <[email protected]> wrote:

> I put up a vapor barrier, then placed the insulation against it,

Did you put the vapour barrier _outside_ the insulation?

Mike

What I have on the exposed concrete section of my workshop is a Dow product
called Polyisocynurate Insulation. It comes with a foil skin on both sides
and is available in various thickness's and R values
1/2"........R3.3
5/8"........R4.1
3/4"........R5.0
1"...........R6.5
1 3/8".....R9.1
1.55"......R10
1 7/8".....R12
2"...........R13
I put up a vapor barrier, then placed the insulation against it, and held it
in place with 2x4" fastened to the exposed studs of the interior walls,
insulated with fiberglass on the studded walls then covered it all with 1/4"
plywood held in place with exterior screws. And I never have to worry about
where I mount things on the wall.

Dave

"Nova" <[email protected]> wrote in message
news:[email protected]...
> Blair Chesterton wrote:
>
> > I am looking for something to insulate the upper four feet of my
basement
> > shop other than the fiberglas insulation I presently use. I don't want
to
> > lose too much space in the shop to walls so I would like to find
something
> > that has a decent "R" value and isnt that thick. What types of methods
are
> > available? I have considered removing this insulation and just having
the
> > poured concrete walls but don't know how much effect that might have on
my
> > heating bill and comfort level.
>
> I'd use styrofoam insulating panels cut to fit between the studs.
>
> --
> Jack Novak
> Buffalo, NY - USA
> (Remove "SPAM" from email address to reply)
>
>