Question for the knowledgeables in the group. I have a Black and
Decker electric sander where the footprint is about 8 inches by 3 1/2
inches. I am considering getting a second sander for more delicate
work and was wondering what would be the choice - 1/4 sheet finishing
sander or a random orbital sander. What are the pros and cons of
both?
Many thanks in advance for your experience.
Ray
Austin, TX
===
"Ray S. & Nayda Katzaman" <[email protected]> wrote in message
news:[email protected]...
> Question for the knowledgeables in the group. I have a Black and
> Decker electric sander where the footprint is about 8 inches by 3 1/2
> inches. I am considering getting a second sander for more delicate
> work and was wondering what would be the choice - 1/4 sheet finishing
> sander or a random orbital sander. What are the pros and cons of
> both?
>
> Many thanks in advance for your experience.
>
Random orbit can be nearly as aggressive as a belt sander. They don't do
narrow edges unless you've got some major wrist strength to keep 'em from
grabbing and rounding, But they produce a nice surface with 220 paper, so
long as you're careful to clean dust out and not press.
My old Rockwell speedbloc - PC now, think its's a 330, gets into all kinds
of corners, doesn't grab on edges, and can be used held between the knees
with small pieces rubbed against the pad to sand them. Excellent sander.
Since you have a half sheet orbital or possibly dual, I know my half sheet
is, I'd do a ROS. Got Bosch myself, kid has the PC and loves it.
On Oct 17, 6:06 pm, ROY! <[email protected]> wrote:
> On Wed, 17 Oct 2007 21:05:02 GMT, "dadiOH" <[email protected]>
> wrote:
>
> >Ray S. & Nayda Katzaman wrote:
> >> Question for the knowledgeables in the group. I have a Black and
> >> Decker electric sander where the footprint is about 8 inches by 3
> >> 1/2 inches. I am considering getting a second sander for more
> >> delicate work and was wondering what would be the choice - 1/4
> >> sheet finishing sander or a random orbital sander. What are the
> >> pros and cons of both?
>
> > Pad sander (1/4 sheet)...easy to use, does good job
>
> >ROS...harder to control, faster
>
> >I'd get the pad sander. And if you someday want a better 1/2 sheet
> >sander than your B&D, get a Porter Cable 505. That and a 1/4 sheet is
> >a winning combo.
>
> Is that 505 a non orbital sander or is it orbital?
It's orbital, with a 1/8" orbit. The 330 is also orbital, but at
5/64". I'm not sure who's making electric in-line sanders.
I almost always touch it by hand before finishing.
JP
I never liked the Porter Cable palm sanders. They have a thick soft
felt behind the paper and it rounds over edges by itself when I am
flat sanding and cros over the edge. I like a hard bottom (not really
a PC statement) like a DeWalt.
In my view a true orbital is very aggressive. I mean the round jobs
with the holes in the face for suction. I even have one air tool tha
is dangerous. I would never use one for finish sanding and rarely use
them at all unless I have some real cutting to do. I put them in the
category of a belt sander. A must have but rarely used. I usually have
a flat wide belt or drum available so all the big flat sanding is done
there. Edges on the edge sander. Palm sander to get things down from
100 to 150 or 220, depending on the material; then finish by hand (no
block) to 150 or 220 depending on the situation to break the edges and
feel a good finish on all important surfaces.
If I am in a production mode and have a big project I will break edges
with 320 or 400 on a palm.
On Oct 18, 6:17 am, "Leon" <[email protected]> wrote:
> "George" <[email protected]> wrote in message
>
> news:%[email protected]...
>
>
>
> > My old Rockwell speedbloc - PC now, think its's a 330, gets into all kinds
> > of corners, doesn't grab on edges, and can be used held between the knees
> > with small pieces rubbed against the pad to sand them. Excellent sander.
>
> I'll agree with the PC SpedBloc. The designh has been around for as long as
> I can remember, longer than some of it's competition has even been in
> business. You cannot go wrong with this sander for finish work.
>
> I also consider replacing the B&D with a good brand ROS. Top of the line
> is probably the Festool Rotex, from there I would go with PC or Bosch.
>
> With these two sanders, sanding is not a headache anymore.
Ray S. & Nayda Katzaman wrote:
> Question for the knowledgeables in the group. I have a Black and
> Decker electric sander where the footprint is about 8 inches by 3
> 1/2 inches. I am considering getting a second sander for more
> delicate work and was wondering what would be the choice - 1/4
> sheet finishing sander or a random orbital sander. What are the
> pros and cons of both?
Pad sander (1/4 sheet)...easy to use, does good job
ROS...harder to control, faster
I'd get the pad sander. And if you someday want a better 1/2 sheet
sander than your B&D, get a Porter Cable 505. That and a 1/4 sheet is
a winning combo.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
Many thanks for the input, information and links provided. I have almost
made up my mind on a 1/4 sheet sander for the more delicate work. Now I
have to tell my daughters where they can get it for me (birthday coming
up next month). I really have to look surprised when I get it.
Again, Thanks!
Ray
Austin, TX
===
"Ray S. & Nayda Katzaman" wrote:
> Question for the knowledgeables in the group. I have a Black and
> Decker electric sander where the footprint is about 8 inches by 3 1/2
> inches. I am considering getting a second sander for more delicate
> work and was wondering what would be the choice - 1/4 sheet finishing
> sander or a random orbital sander. What are the pros and cons of
> both?
>
> Many thanks in advance for your experience.
>
> Ray
> Austin, TX
> ===
"George" <[email protected]> wrote in message
news:%[email protected]...
>
> My old Rockwell speedbloc - PC now, think its's a 330, gets into all kinds
> of corners, doesn't grab on edges, and can be used held between the knees
> with small pieces rubbed against the pad to sand them. Excellent sander.
I'll agree with the PC SpedBloc. The designh has been around for as long as
I can remember, longer than some of it's competition has even been in
business. You cannot go wrong with this sander for finish work.
I also consider replacing the B&D with a good brand ROS. Top of the line
is probably the Festool Rotex, from there I would go with PC or Bosch.
With these two sanders, sanding is not a headache anymore.
On Wed, 17 Oct 2007 20:53:23 GMT, "Ray S. & Nayda Katzaman"
<[email protected]> wrote:
>Question for the knowledgeables in the group. I have a Black and
>Decker electric sander where the footprint is about 8 inches by 3 1/2
>inches. I am considering getting a second sander for more delicate
>work and was wondering what would be the choice - 1/4 sheet finishing
>sander or a random orbital sander. What are the pros and cons of
>both?
>
>Many thanks in advance for your experience.
>
>Ray
>Austin, TX
>===
I found that my orbital sander is more aggressive than my finishing
sander. The finishing sander has a square bottom which can be useful
in some applications. The finishing sander uses regular sandpaper,
but the dust holes have to be punched out. Having both sanders is
the best choice.
Ray S. & Nayda Katzaman wrote:
> Question for the knowledgeables in the group. I have a Black and
> Decker electric sander where the footprint is about 8 inches by 3 1/2
> inches. I am considering getting a second sander for more delicate
> work and was wondering what would be the choice - 1/4 sheet finishing
> sander or a random orbital sander. What are the pros and cons of
> both?
>
> Many thanks in advance for your experience.
'pends...on what kind of work you do and what you're expecting. For
most finishing sanding, I'd opt for the 5" ROS unless it is very large
surfaces.
--
Jay Pique wrote:
> On Oct 17, 6:06 pm, ROY! <[email protected]> wrote:
>> On Wed, 17 Oct 2007 21:05:02 GMT, "dadiOH" <[email protected]>
>> wrote:
>>
>>> Ray S. & Nayda Katzaman wrote:
>>>> Question for the knowledgeables in the group. I have a Black and
>>>> Decker electric sander where the footprint is about 8 inches by 3
>>>> 1/2 inches. I am considering getting a second sander for more
>>>> delicate work and was wondering what would be the choice - 1/4
>>>> sheet finishing sander or a random orbital sander. What are the
>>>> pros and cons of both?
>>
>>> Pad sander (1/4 sheet)...easy to use, does good job
>>
>>> ROS...harder to control, faster
>>
>>> I'd get the pad sander. And if you someday want a better 1/2
>>> sheet
>>> sander than your B&D, get a Porter Cable 505. That and a 1/4
>>> sheet
>>> is a winning combo.
>>
>> Is that 505 a non orbital sander or is it orbital?
>
> It's orbital, with a 1/8" orbit. The 330 is also orbital, but at
> 5/64". I'm not sure who's making electric in-line sanders.
>
> I almost always touch it by hand before finishing.
The Porter-Cable 9444VS is inline. It's a piece of crap, but it's
inline. The Festool LS130 is inline--never used it so can't comment.
Personally I've got a half-sheet Craftsman Professional from some time
in the early '80s that is dual-mode--it can be switched from orbital
to linear--it's not the greatest sander in the world but it works when
I need it.
--
--
--John
to email, dial "usenet" and validate
(was jclarke at eye bee em dot net)
"SonomaProducts.com" <[email protected]> wrote in message
news:[email protected]...
>I never liked the Porter Cable palm sanders. They have a thick soft
> felt behind the paper and it rounds over edges by itself when I am
> flat sanding and cros over the edge. I like a hard bottom (not really
> a PC statement) like a DeWalt.
Actually the PC SpedBloc does not have felt, rather a dense foam rubber pad
that is about 1/2" thick. I never have a round over problem on the corners
unless I am edge sanding. Over the edge of a wide flat surface has never
been a problem for me with this sander.
> In my view a true orbital is very aggressive.
Agreed, A ROS, not so agressive. That said, the Rotex will sand in both
modes.
I mean the round jobs
> with the holes in the face for suction.
ROS's use that paper also.
On Wed, 17 Oct 2007 21:05:02 GMT, "dadiOH" <[email protected]>
wrote:
>Ray S. & Nayda Katzaman wrote:
>> Question for the knowledgeables in the group. I have a Black and
>> Decker electric sander where the footprint is about 8 inches by 3
>> 1/2 inches. I am considering getting a second sander for more
>> delicate work and was wondering what would be the choice - 1/4
>> sheet finishing sander or a random orbital sander. What are the
>> pros and cons of both?
>
> Pad sander (1/4 sheet)...easy to use, does good job
>
>ROS...harder to control, faster
>
>I'd get the pad sander. And if you someday want a better 1/2 sheet
>sander than your B&D, get a Porter Cable 505. That and a 1/4 sheet is
>a winning combo.
Is that 505 a non orbital sander or is it orbital?
ROY!