"cc" <[email protected]> wrote in news:1173329553.614728.254650@
64g2000cwx.googlegroups.com:
> Using 1/8" dark brown hardboard as drawer bottom for very small
> drawers with little load..color is too dark(brown)..can you paint
> hardboard and will it stick to the slick surface? Assume a slight
> sanding to rough the surface and enamel paint will work..anyone tried
> this?
>
I've done it... In fact the paint was a little wet the next day at the
train show. ;-)
Some materials you can get away with not priming before you paint, but
definately prime the hardboard. If your primer's naturally thicker, that
may be a good thing. (Don't apply a thick coat, that has a tendency to
chip and flake.)
I put two coats of white primer on the hardboard before I felt it was
ready for the sky blue. Remember, it's easier to go light to dark than
dark to light.
Puckdropper
--
Wise is the man who attempts to answer his question before asking it.
To email me directly, send a message to puckdropper (at) fastmail.fm
"cc" <[email protected]> wrote in message
news:[email protected]...
> Using 1/8" dark brown hardboard as drawer bottom for very small
> drawers with little load..color is too dark(brown)..can you paint
> hardboard and will it stick to the slick surface? Assume a slight
> sanding to rough the surface and enamel paint will work..anyone tried
> this?
>
Yes you can paint the hardboard. My grand mother and brother in-law do
paintings on hardboard/Masonite, the smooth hardboards woul probably be the
easiest to paint and keep clean.
"Lew Hodgett" <[email protected]> wrote in message
news:[email protected]...
> Leon wrote:
>
> > Actually, artists use Masonite/hardboard to paint on, the smooth side.
>
>
> An artist's rendition might look neat on a drawer bottom, but wouldn't
> expect it to wear very well.
>
> Think I'll stick with the prefinished panel.
>
> Lew
>
>
But what a treat and surprise when you looked inside the drawer. LOL
We restore vintage travel trailers and some of our work has been done on
trailers from the thirties and forties which were originally skinned in
masonite and painted. We just prime and paint the replacement masonite. No
sanding required. The trailer on my home webpage is skinned in masonite with
a canvas covered roof! Check it out here. www.vintagetrailersforsale.com
Good luck,
cm
"cc" <[email protected]> wrote in message
news:[email protected]...
> Using 1/8" dark brown hardboard as drawer bottom for very small
> drawers with little load..color is too dark(brown)..can you paint
> hardboard and will it stick to the slick surface? Assume a slight
> sanding to rough the surface and enamel paint will work..anyone tried
> this?
>
"Lew Hodgett" <[email protected]> wrote in message
news:[email protected]...
> cc wrote:
> > Using 1/8" dark brown hardboard as drawer bottom for very small
> > drawers with little load..color is too dark(brown)..can you paint
> > hardboard and will it stick to the slick surface? Assume a slight
> > sanding to rough the surface and enamel paint will work..anyone tried
> > this?
> >
>
> I'd use low cost, prefinished paneling.
>
> Hard board will soak up a ton of paint and still look like crap.
Actually, artists use Masonite/hardboard to paint on, the smooth side.
cc wrote:
> Using 1/8" dark brown hardboard as drawer bottom for very small
> drawers with little load..color is too dark(brown)..can you paint
> hardboard and will it stick to the slick surface? Assume a slight
> sanding to rough the surface and enamel paint will work..anyone tried
> this?
>
I'd use low cost, prefinished paneling.
Hard board will soak up a ton of paint and still look like crap.
Lew