I am using Minwax wipe-on poly on a cherry cabinet. The are a lot of little
cubbies that are a bear to get into. They will not get any wear and will
always be in shadow.
Can I get by with a single coat in the deep recesses? If not, maybe I will
have to pay my 10 year old to do them, cause my hand really doesn't fit.
For next time, should I have varnished them all before assembly? (I relied
on friction and "precision" stop dados, no glue.)
Bob Schmall wrote:
>
>
> I'm in the middle of building a stereo cabinet, and in this case (har!) it
> will be impossible to get behind the drawers after assembly. I plan to
> finish before assembly, with maybe just one last coat after assembly.
I did an experiment on a set of kitchen cabinets, the complicated one was
finished before assembly, the easy one I finished after assembly.
If I can at all avoid it I will never again finish anything with a hard coat
after assembly.
Well, then again, there are always exceptions. I don't foresee them at this time.
--
Mark
N.E. Ohio
Never argue with a fool, a bystander can't tell you apart. (S. Clemens, A.K.A.
Mark Twain)
When in doubt hit the throttle. It may not help but it sure ends the suspense.
(Gaz, r.moto)
"Toller" <[email protected]> wrote in message
news:[email protected]...
> I am using Minwax wipe-on poly on a cherry cabinet. The are a lot of
little
> cubbies that are a bear to get into. They will not get any wear and will
> always be in shadow.
>
> Can I get by with a single coat in the deep recesses? If not, maybe I
will
> have to pay my 10 year old to do them, cause my hand really doesn't fit.
The rule of thumb is to apply exactly the same number to both sides, to
prevent wood movement. I'm not necessarily recommending this--the piece may
be solid enough to resist movement on its own. YMMV, void where prohibited,
etc.
> For next time, should I have varnished them all before assembly? (I relied
> on friction and "precision" stop dados, no glue.)
I'm in the middle of building a stereo cabinet, and in this case (har!) it
will be impossible to get behind the drawers after assembly. I plan to
finish before assembly, with maybe just one last coat after assembly.
Bob
Bob
Bob
"Mark" <[email protected]> wrote in message
news:MEnic.64558$B%[email protected]...
>
>
> Bob Schmall wrote:
>
> >
> >
> > I'm in the middle of building a stereo cabinet, and in this case (har!)
it
> > will be impossible to get behind the drawers after assembly. I plan to
> > finish before assembly, with maybe just one last coat after assembly.
>
>
>
> I did an experiment on a set of kitchen cabinets, the complicated one was
> finished before assembly, the easy one I finished after assembly.
>
> If I can at all avoid it I will never again finish anything with a hard
coat
> after assembly.
>
> Well, then again, there are always exceptions. I don't foresee them at
this time.
i agree. i always try and bring the work to me whenever possible instead of
bringing me (and my sore back) to the wood.
randy
Could you make an applicator pad stapled to a stick to reach into the
cubbies? If you're like me you have a plethor of hardwood "paint sticks"
which are ideal for this purpose. :-)
I would go for at least 2 applications. The first pass soaks into the wood,
only on the second pass do you get any build. I would expect the sheen to
change significantly between coats one and two, but less so after that.
Thinning may help you get into the corners some.
-Steve
"Toller" <[email protected]> wrote in message
news:[email protected]...
> I am using Minwax wipe-on poly on a cherry cabinet. The are a lot of
little
> cubbies that are a bear to get into. They will not get any wear and will
> always be in shadow.
>
> Can I get by with a single coat in the deep recesses? If not, maybe I
will
> have to pay my 10 year old to do them, cause my hand really doesn't fit.
>
> For next time, should I have varnished them all before assembly? (I relied
> on friction and "precision" stop dados, no glue.)
>
>
>