In article <[email protected]>, Tom Young
<[email protected]> wrote:
> I was wondering how it would work to take a 2x2 and instead
> of spending a lot of time tapering, put a couple of door shims under the
> middle to make the bow.
Your clamping pressure would be focussed on the shims, methinks.
--
Okay, so this is my new sig line, eh?
"Tom Young" <[email protected]> wrote in message
news:[email protected]...
> A project I'm working on suggests using cauls for gluing up the carcase of
a
> shelf. Is there anything special about cauls or are they only something
> like a 2x2 to even up the pressure of the clamps?
>
> Thanks
> Tom
>
>
A caul can be made of anything. I use scraps because I usually make it
specific to joint being clamped. Depending on the situation, you might want
to put wax paper between the caul and the project being clamped. It is
pretty sad when you realize that you have attached the caul to the project.
Bob
"Dave Balderstone" <dave@N_O_T_T_H_I_S.balderstone.ca> wrote in message
news:100420040749370044%dave@N_O_T_T_H_I_S.balderstone.ca...
> > I was wondering how it would work to take a 2x2 and instead
> > of spending a lot of time tapering, put a couple of door shims under the
> > middle to make the bow.
>
> Your clamping pressure would be focussed on the shims, methinks.
>
Wouldn't the shims go on the outer portion so as to flex in the center?
Ed
Ditto what everyone else said and also,
Judge the pressure of a clamp head radiating (fanning out)
on a line of 45 degrees each side of the clamp head. This
90 degree (2 X 45) arc is the area the clamp head is
exerting pressure to/on. By pulling the clamp head away
from what's being clamped the width of this "pressure area"
is widened. With a caul a wider area can be clamped using
fewer clamps.
The above is also true when gluing up boards into panels.
Let's say you are gluing up two boards 5" wide. The first
clamp can be positioned 5" (the width of your board) in from
the end. The remaining clamps can be position 10" (twice
the width of your boards) on center with the last one 5"
from the end. Any more than that is overkill and of course
it never works out to be exact but the idea is to be as
close as possible without beating yourself up over it.
This is not to say that if your stock is good and true you
cannot get by with less, just that if you are ever
wondering, this is a good rule to go by.
Your Mileage May Vary and Bingo Was His Name-O.
Oh, and before I forget, cauls are tools. It doesn't hurt
to have a few on hand. They can be made from left over
scraps and stored away until needed.
UA100
Thanks for the info. Wouldn't you know, I just cleaned the shop and burned
the scrap pile? I was wondering how it would work to take a 2x2 and instead
of spending a lot of time tapering, put a couple of door shims under the
middle to make the bow.
Tom
"Tom Young" <[email protected]> wrote in message
news:[email protected]...
> A project I'm working on suggests using cauls for gluing up the carcase of
a
> shelf. Is there anything special about cauls or are they only something
> like a 2x2 to even up the pressure of the clamps?
>
> Thanks
> Tom
>
>
---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.634 / Virus Database: 406 - Release Date: 3/18/04
In article <[email protected]>, [email protected]
says...
> Thanks for the info. Wouldn't you know, I just cleaned the shop and burned
> the scrap pile? I was wondering how it would work to take a 2x2 and instead
> of spending a lot of time tapering, put a couple of door shims under the
> middle to make the bow.
>
Takes me about 2 minutes per 4' caul with a hand plane.
--
Where ARE those Iraqi WMDs?
Ok two minutes and a hand plane. What could be easier.
Thanks
tom
"Larry Blanchard" <[email protected]> wrote in message
news:[email protected]...
> In article <[email protected]>, [email protected]
> says...
> > Thanks for the info. Wouldn't you know, I just cleaned the shop and
burned
> > the scrap pile? I was wondering how it would work to take a 2x2 and
instead
> > of spending a lot of time tapering, put a couple of door shims under the
> > middle to make the bow.
> >
> Takes me about 2 minutes per 4' caul with a hand plane.
>
> --
> Where ARE those Iraqi WMDs?
---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.634 / Virus Database: 406 - Release Date: 3/18/04
On Fri, 9 Apr 2004 21:14:01 -0500, "Tom Young" <[email protected]> wrote:
>A project I'm working on suggests using cauls for gluing up the carcase of a
>shelf. Is there anything special about cauls or are they only something
>like a 2x2 to even up the pressure of the clamps?
>
>Thanks
>Tom
>
They are something like a 2x2 as you say. They are used to distribute clamp pressure over areas that otherwise probably wouldn't see
any pressure. The only thing special about them is that they are usually tapered or curved somewhat to be slightly thicker (in the
clamping direction) at the center than at the ends where the clamps are applied. The reason for that is to insure that as the caul
flexes under load, the center still exerts roughly as much pressure as the ends.
Tom Veatch
Wichita, KS USA
Yes, a caul is used to clamp and spread the clampingvforce across the entire
span as well as lining the board edges/ Typically they are a bit thicker
in the middle. When clamped on the ends, the thicker part, (actually a bit
of bow) squeezes the middle. Hardwood with a 1/4 " bow is usually enough/
The piece may be two inches thick, with the middle three inches and the
ends 2 3/4 thick. This span would be good for a two to three foot span.