I made a CD cabinet with the intention of using the CD holder strip (6
ft long) black plastic from Rockler to the wood sides. When I
received the CD holder it had a very tiny strip of adhesive on paper
to hold the plastic strip in place. It might have worked except that
you only got one try on locating the strip on the wood. With problems
of horizonal alignment between the opposing strips needless to say it
didn't stick well.
I then used DAP Weldwood Contact Cement on the wooden sides. It stuck
on but not too well.I left the cabinet in the back of my van and it
got hot and the plastic expanded an bit and buckled in some spots. It
may stick back down. Time will tell.
Does anyone have any suggestions for this time or for the future, if I
decide to make another one?
Regards, Al
On Aug 27, 11:33 pm, [email protected] wrote:
> Well, one thought comes to mind, set up a jig on your tablesaw like
> you would for a box joint. (the guide pin system) but make it the
> width for CD cases. Then you could just notch a series of wood strips
> and place them in the project to hold the cd's.
>
>I had thought of that at the start of the project, but thought that buying the plastic holders would be easier and look better. The plastic still looks good, but was more tricky to get in alignment, more of a problem than I would have had with either a wooden strips or cutting into the sides of the cabinet from the start.
Thanks for the suggestion.
Al
I've used these
http://wwhardware.com/catalog.cfm/GroupID/Entertainment%20Hardware/CatID/Media%20Storage/SubCatID/CD%2C%20DVD%20and%20VHS%20Organizers
(look at Push and Release CD Holder).
They should\may retro-fit into you box. I included them in a pretty
succesful product line. They hold 20 per set. I typically put in
dividers for each section on longer boxes but thay can be butted with
just a slight different spacing at each butt. They hold the CD's
securly. A single push and release of a CD pops it out, its a really
cool mechanism.
They come with screws and install in a very secure manner. I found I
had to use a very low profile right angle drill driver to access the
screws along the back side (inside the box). (Dewalt worked fine but
old Mikita was better). A short hand driver would work depending on th
material or if you can get an awl in to mak a pilot.
On Aug 27, 7:48 pm, Al Holstein <[email protected]> wrote:
> I made a CD cabinet with the intention of using the CD holder strip (6
> ft long) black plastic from Rockler to the wood sides. When I
> received the CD holder it had a very tiny strip of adhesive on paper
> to hold the plastic strip in place. It might have worked except that
> you only got one try on locating the strip on the wood. With problems
> of horizonal alignment between the opposing strips needless to say it
> didn't stick well.
>
> I then used DAP Weldwood Contact Cement on the wooden sides. It stuck
> on but not too well.I left the cabinet in the back of my van and it
> got hot and the plastic expanded an bit and buckled in some spots. It
> may stick back down. Time will tell.
>
> Does anyone have any suggestions for this time or for the future, if I
> decide to make another one?
>
> Regards, Al
Al Holstein wrote:
> I made a CD cabinet with the intention of using the CD holder strip (6
> ft long) black plastic from Rockler to the wood sides. When I
> received the CD holder it had a very tiny strip of adhesive on paper
> to hold the plastic strip in place. It might have worked except that
> you only got one try on locating the strip on the wood. With problems
> of horizonal alignment between the opposing strips needless to say it
> didn't stick well.
>
> I then used DAP Weldwood Contact Cement on the wooden sides. It stuck
> on but not too well.I left the cabinet in the back of my van and it
> got hot and the plastic expanded an bit and buckled in some spots. It
> may stick back down. Time will tell.
>
> Does anyone have any suggestions for this time or for the future, if I
> decide to make another one?
>
> Regards, Al
>
I didn't find alignment a problem. I just made sure that I had the
strips for both sides trimmed the same at the starting point, so that as
long as I started at the top or bottom of the opening the strips would
have to line up with each other.
I did find the Rockler strips to be somewhat lacking in the adhesive
department... some of the glue came off with the paper backing. I used a
few strategically-placed dabs of plain old yellow wood glue where
needed, and it worked just fine.
"Ron Magen" wrote:
> OK, I'll bite . . . . Where is it, or did you modify some ' . . .
> measured
> drawing . .' to suit? Couldn't find any 'specific' plan/shelf on the NYW
> site.
It's listed as CD Storage, #0104
I added a 3rd row so you end up with a 3x3 grid, the bottom row being taller
and it accepts DCD's
Lew
Well, one thought comes to mind, set up a jig on your tablesaw like
you would for a box joint. (the guide pin system) but make it the
width for CD cases. Then you could just notch a series of wood strips
and place them in the project to hold the cd's.
>Does anyone have any suggestions for this time or for the future, if I
>decide to make another one?
>
On Mon, 27 Aug 2007 19:48:51 -0700, Al Holstein <[email protected]>
wrote:
>I made a CD cabinet with the intention of using the CD holder strip (6
>ft long) black plastic from Rockler to the wood sides. When I
>received the CD holder it had a very tiny strip of adhesive on paper
>to hold the plastic strip in place. It might have worked except that
>you only got one try on locating the strip on the wood. With problems
>of horizonal alignment between the opposing strips needless to say it
>didn't stick well.
>
>I then used DAP Weldwood Contact Cement on the wooden sides. It stuck
>on but not too well.I left the cabinet in the back of my van and it
>got hot and the plastic expanded an bit and buckled in some spots. It
>may stick back down. Time will tell.
>
>Does anyone have any suggestions for this time or for the future, if I
>decide to make another one?
Horizontal alignment should be taken care of by running the strips the
full length of the compartment.
Is there enough thickness to countersink some small black screws
anywhere? Or put them between the cds?
-Leuf
Lew,
OK, I'll bite . . . . Where is it, or did you modify some ' . . . measured
drawing . .' to suit? Couldn't find any 'specific' plan/shelf on the NYW
site.
I have plans for a 'Lighthouse Shelf' I was going to modify specifically for
CD's. However, I'm always open to other ideas . . .
Regards & Thanks,
Ron Magen
"Lew Hodgett" <[email protected]> wrote
>
> Use the NYW plan.
>
> I did and am very satisfied with the results.
>
> BTW, I modified the plan to include DVDs and CDs.
>
> Holds about 200 CDs and 100 DVDs.
>
> Lew