HotRod wrote:
> If you've read m other post I need to make a double sided finger board at
> least 25" long. In this case it means a ton of cuts. I was wondering if
> anyone had any ideas for evenly spacing all of the cuts quickly?
Small, shopmade miter box and an 0.002" "Blitz" aka Eberle model
railroader's backsaw. Lay out all fret slots relative to the nut. The
compass trick where you swing arcs from the frets is nearly impossible
to pull off accurately due to accumulated error.
Send the wife and kids out to a movie, and consider decaf. You
want to get into a deep Zen theta state with no distractions.
Look at the TS miter jigs made for doing finger joints. You could setup
something similar with an index pin. After you make the first cut you
move it over the index pin, then rinse and repeat.
HotRod wrote:
> If you've read m other post I need to make a double sided finger board at
> least 25" long. In this case it means a ton of cuts. I was wondering if
> anyone had any ideas for evenly spacing all of the cuts quickly?
Look at the TS miter jigs made for doing finger joints or box joints.
They use a little pin that fits into the last cut. You could setup
something similar with a slanted index pin. After you make the first
cut you move it over the index pin, then rinse and repeat.
HotRod wrote:
> If you've read m other post I need to make a double sided finger board at
> least 25" long. In this case it means a ton of cuts. I was wondering if
> anyone had any ideas for evenly spacing all of the cuts quickly?
CW wrote:
> Would someone please explain to me what the OP means by "finger board"? He
> said, at the beginning of this thread, about seeing his other thread. Well,
> I didn't see it and have no idea. If he is, as some have implied, making a
> fingerboard for a stringed instrument, half of these replies are useless
> information (for this project). Stringed instrument fingerboards are NOT
> evenly spaced.
>
> "Mike Marlow" <[email protected]> wrote in message
> news:[email protected]...
>>
>> "Mike Marlow" <[email protected]> wrote in message
>> news:[email protected]...
>> >
>> > "HotRod" <[email protected]> wrote in message
>> > news:[email protected]...
>> > > If you've read m other post I need to make a double sided finger board
>> at
>> > > least 25" long. In this case it means a ton of cuts. I was wondering
> if
>> > > anyone had any ideas for evenly spacing all of the cuts quickly?
>> > >
>> > >
>> >
>> > Why wouldn't making the cuts on each end, moving the fence and then
> making
>> > the next cuts be fast enough? The secret to making evenly spaced cuts
> is
>> to
>> > move the fence by the same amount each time. Not much of a secret, huh?
>> Oh
>> > well - if it was a secret I wouldn't have been able to tell you.
>> >
>>
>> Nix on this post. After I sent it I realized that I had mixed it up with
>> another thread.
>>
>> --
>>
>> -Mike-
>> [email protected]
>>
>>
>
>
I believe he means a featherboard, to hold material in alignment as it
passes through a sander or some such. His previous post actually calls
it a featherboard instead of a finger board. I too have my moments.
--
Gerald Ross
Cochran, GA
An evil mind is a constant solace.
"Mike Marlow" <[email protected]> wrote in message
news:[email protected]...
>
> "HotRod" <[email protected]> wrote in message
> news:[email protected]...
> > If you've read m other post I need to make a double sided finger board
at
> > least 25" long. In this case it means a ton of cuts. I was wondering if
> > anyone had any ideas for evenly spacing all of the cuts quickly?
> >
> >
>
> Why wouldn't making the cuts on each end, moving the fence and then making
> the next cuts be fast enough? The secret to making evenly spaced cuts is
to
> move the fence by the same amount each time. Not much of a secret, huh?
Oh
> well - if it was a secret I wouldn't have been able to tell you.
>
Nix on this post. After I sent it I realized that I had mixed it up with
another thread.
--
-Mike-
[email protected]
"Gerald Ross" <[email protected]> wrote in message
news:[email protected]...
> CW wrote:
> > Would someone please explain to me what the OP means by "finger board"?
He
> > said, at the beginning of this thread, about seeing his other thread.
Well,
> > I didn't see it and have no idea. If he is, as some have implied, making
a
> > fingerboard for a stringed instrument, half of these replies are useless
> > information (for this project). Stringed instrument fingerboards are NOT
> > evenly spaced.
> >
> >
> I believe he means a featherboard, to hold material in alignment as it
> passes through a sander or some such. His previous post actually calls
> it a featherboard instead of a finger board. I too have my moments.
>
That's what I originally thought with my replies. If that's the case, then
I would stand by my suggestion earlier posted. Reading through other
replies I thought I had goofed up and that the OP was talking about finger
joints. I saw the posts about fret spacing and just assumed those posters
misunderstood the OP.
Oye - this one is taking too much work.
--
-Mike-
[email protected]
Actually on a guitar fingerboard the spaces are not equal in any way
except depth. Also there is a crown on the visible face of the fret
board. I would suggest you hit Stewart-MacDonald's web site at
http://www.stewmac.com and look at buying a fret board template
http://www.stewmac.com/cgi-bin/hazel.cgi?action=SERVE&sku=4915&ITEM=catalog/sku.html
and their fret cutting table saw blade.
http://www.stewmac.com/shop/Fretting_supplies/Saws_and_slots/Custom_Table_Saw_Fret_Slotting_Blade.html
Their instructions are very good. There are quiet a few online tools
buried throughout the site.
On Wed, 17 Jan 2007 18:56:59 -0500, "HotRod" <[email protected]>
wrote:
>If you've read m other post I need to make a double sided finger board at
>least 25" long. In this case it means a ton of cuts. I was wondering if
>anyone had any ideas for evenly spacing all of the cuts quickly?
>
Thank you.
"Gerald Ross" <[email protected]> wrote in message
news:45b04bfe$0$9722> I believe he means a featherboard, to hold material in
alignment as it
> passes through a sander or some such. His previous post actually calls
> it a featherboard instead of a finger board. I too have my moments.
"HotRod" wrote:
> If you've read m other post I need to make a double sided finger
board at
> least 25" long. In this case it means a ton of cuts. I was
wondering if
> anyone had any ideas for evenly spacing all of the cuts quickly?
You could make an indexing fence using a couple of 3/8-16 pieces of
threaded rod, some nuts and a couple of pieces of wood.
One piece of wood is clamped to saw table to serve as a fixed fence.
2nd piece of wood is about 12" long and parallel to long piece.
The two pieces of wood are connected together with the threaded rods
with the wood having thru holes, using nuts to lock in place.
Since threaded rod has 16 threads/inch, one revolution of nut = 1/16".
Now have the means to index the smaller wooden piece as req'd to make
equally spaced cuts.
Lew
"HotRod" <[email protected]> wrote in message
news:[email protected]...
> If you've read m other post I need to make a double sided finger board at
> least 25" long. In this case it means a ton of cuts. I was wondering if
> anyone had any ideas for evenly spacing all of the cuts quickly?
>
>
Why wouldn't making the cuts on each end, moving the fence and then making
the next cuts be fast enough? The secret to making evenly spaced cuts is to
move the fence by the same amount each time. Not much of a secret, huh? Oh
well - if it was a secret I wouldn't have been able to tell you.
--
-Mike-
[email protected]
On Wed, 17 Jan 2007 18:56:59 -0500, "HotRod" <[email protected]>
wrote:
>If you've read m other post I need to make a double sided finger board at
>least 25" long. In this case it means a ton of cuts. I was wondering if
>anyone had any ideas for evenly spacing all of the cuts quickly?
>
Set up an indexing pin. Once that is done, the cuts are quick work. I
have also made a finger board by gluing lined paper to the piece of
wood--either cutting with a bandsaw or table saw.
"Lew Hodgett" <[email protected]> wrote in message
news:[email protected]...
> "HotRod" wrote:
>
> > If you've read m other post I need to make a double sided finger
> board at
> > least 25" long. In this case it means a ton of cuts. I was
> wondering if
> > anyone had any ideas for evenly spacing all of the cuts quickly?
>
> You could make an indexing fence using a couple of 3/8-16 pieces of
> threaded rod, some nuts and a couple of pieces of wood.
>
> One piece of wood is clamped to saw table to serve as a fixed fence.
>
> 2nd piece of wood is about 12" long and parallel to long piece.
>
> The two pieces of wood are connected together with the threaded rods with
> the wood having thru holes, using nuts to lock in place.
>
> Since threaded rod has 16 threads/inch, one revolution of nut = 1/16".
>
> Now have the means to index the smaller wooden piece as req'd to make
> equally spaced cuts.
TS Aligner?
Would someone please explain to me what the OP means by "finger board"? He
said, at the beginning of this thread, about seeing his other thread. Well,
I didn't see it and have no idea. If he is, as some have implied, making a
fingerboard for a stringed instrument, half of these replies are useless
information (for this project). Stringed instrument fingerboards are NOT
evenly spaced.
"Mike Marlow" <[email protected]> wrote in message
news:[email protected]...
>
> "Mike Marlow" <[email protected]> wrote in message
> news:[email protected]...
> >
> > "HotRod" <[email protected]> wrote in message
> > news:[email protected]...
> > > If you've read m other post I need to make a double sided finger board
> at
> > > least 25" long. In this case it means a ton of cuts. I was wondering
if
> > > anyone had any ideas for evenly spacing all of the cuts quickly?
> > >
> > >
> >
> > Why wouldn't making the cuts on each end, moving the fence and then
making
> > the next cuts be fast enough? The secret to making evenly spaced cuts
is
> to
> > move the fence by the same amount each time. Not much of a secret, huh?
> Oh
> > well - if it was a secret I wouldn't have been able to tell you.
> >
>
> Nix on this post. After I sent it I realized that I had mixed it up with
> another thread.
>
> --
>
> -Mike-
> [email protected]
>
>